Formwork

General information

Our offer includes a wide selection of formwork systems available to buy or rent.

Our products allow to build virtually any facility in a simple, quick, economical and safe manner.

We offer wall formwork (light and heavy), square and rectangular pole forming systems, elevator pit formwork, column formwork, ceiling formwork and support towers.

Wall formwork

Frame formwork structures made of 12 cms thick steel profiles, hot-dip galvanized and filled with a special 15 mm thick plywood plating.

A full range of wall formwork systems where all boards are compatible, complementary and exchangeable, allows for perfect design of a formwork for any walls.

If the full range of system elements are used, it is possible to easily build virtually any facility in a simple, quick, economical and safe manner.

We offer compatible wall formwork systems, which include:

Light wall formwork MIDI BOX [60 kN/m2]

An economic small- and medium-sized system for manual assembly with the height of boards from 90 cm to 270 cm and widths from 25 cm to 90 cm.

The system constitutes both a supplement and an alternative to heavy boards. Boards intended for foundations, binders, and typical concrete walls. The boards transfer the pressure of fresh concrete to 60 kN/m².

Heavy wall formwork MIDI BOX [80 kN/m2]

It is a wall formwork, thanks to which its assembly on the construction site is possible only with the use of a crane – boards in the range of 90 to 240 cm.
Permissible fresh concrete pressure for the MIDI BOX formwork is:

80 kN/m² – for settings without superstructures – 55 kN/m² – for settings with superstructures.

The multifunctional BM260 and BM710 formwork locks reliably connect shuttering boards, fasten corners and columns, and also serve the function of straightening the formwork plane. Additional stiffening for larger wall surfaces (both vertical and horizontal) is achieved by using shuttering and stiffening beams that replace the BM710 lock.

Walls with a height of 270 cm, 300 cm are joined with three BM260 locks per one board joint. We connect the formwork boards in extensions by using BM710 locks, which have a longer pressure foot (710 mm), which results in that the plane straightening the formwork is larger. Using radial slats, it is possible to shutter polygonal constructions with a radius of more than 2.5 m. With three widths of radial slats at 15, 20, and 25 cm and all boards to choose from, it is possible to precisely combine tailor-made formworks. The radial slats are connected with the boards using alternate centering ties.

To complete the length of walls, use supplementary inserts. It is a perfect solution when it is not possible to obtain the required length of the formwork based on a shuttering board system. Then, insert wooden or steel inserts between the boards.

The alignment of formwork boards is allowed by means of:

  • tilting support – used for the alignment of formwork boards up to the height of 3 m,
  • diagonal support – used for the alignment of wall formwork with the height above 3 m.

Formworks enable the selection of boards with a module every 5 cm vertically and horizontally. Formwork boards can be combined with each other in any configuration. It has to be remembered that the basic arrangement of the boards is the vertical. The horizontal arrangement should be considered as a complementary solution.

Dimensions of shuttering panels

Height

Width

Post width

90 cm

25, 30, 45, 50, 55, 60, 65, 70

75, 90

120 cm

25, 30, 45, 50, 55, 60, 65, 70

75, 90

150 cm

25, 30, 45, 50, 55, 60, 65, 70

90

270 cm

25, 30, 45, 50, 55, 60, 65, 70

75, 90, 120, 180, 240

300 cm

25, 30, 45, 50, 55, 60, 65, 70

75, 90, 240